Xilinx Tools: Difference between revisions
New page: '''Frame Generation Tool'''<br><br> '''''General'''''<br> This tool can be used to generate frames for any Xilinx Virtex-II Pro FPGA. Therefore an XML based configuration file exists. To g... |
mNo edit summary |
||
| Line 1: | Line 1: | ||
==Frame Generation Tool== | |||
===General=== | |||
This tool can be used to generate frames for any Xilinx Virtex-II Pro FPGA. Therefore an XML based configuration file exists. To generate frame files the type of FPGA has to be added to the XML file. | This tool can be used to generate frames for any Xilinx Virtex-II Pro FPGA. Therefore an XML based configuration file exists. To generate frame files the type of FPGA has to be added to the XML file. | ||
This is done in the following way: | This is done in the following way: | ||
<Device DeviceName="XC2VP7" DeviceID="0124A093" numFrames="1320" frameLength="106" IOBColumns="2" IOBFrames="4" IOIColumns="2" IOIFrames="22" CLBColumns="34" CLBFrames="22" BRAMColumns="6" BRAMFrames="64" BRAMICColumns="6" BRAMICFrames="22" GCLKColumns="1" GCLKFrames="4"><br><br> | <Device DeviceName="XC2VP7" DeviceID="0124A093" numFrames="1320" frameLength="106" IOBColumns="2" IOBFrames="4" IOIColumns="2" IOIFrames="22" CLBColumns="34" CLBFrames="22" BRAMColumns="6" BRAMFrames="64" BRAMICColumns="6" BRAMICFrames="22" GCLKColumns="1" GCLKFrames="4"><br><br> | ||
The device name can be found directly on the chip. The other values are provided in the Xilinx User Guide in the chapter “Configuration – Configuration Details”. There you will find two tables in which all frame and column sizes are listed. The device IDs you will also find in a table in this chapter. | The device name can be found directly on the chip. The other values are provided in the Xilinx User Guide in the chapter “Configuration – Configuration Details”. There you will find two tables in which all frame and column sizes are listed. The device IDs you will also find in a table in this chapter. | ||
For different types of Virtex FPGAs the names of the frame types can vary. The names shown above are an example for Virtex-II Pro frames. | For different types of Virtex FPGAs the names of the frame types can vary. The names shown above are an example for Virtex-II Pro frames. | ||
<br> | <br> | ||
===Creating frames=== | |||
Generating the frames is done in these steps: | Generating the frames is done in these steps: | ||
1. Load the bit-file for the FPGA | 1. Load the bit-file for the FPGA | ||
2. Type the name of the device as you can see above in “DeviceName” | 2. Type the name of the device as you can see above in “DeviceName” | ||
3. Load the XML configuration file | 3. Load the XML configuration file | ||
4. Type the directory where the frames are saved to | 4. Type the directory where the frames are saved to | ||
5. Press the “Split” button | 5. Press the “Split” button | ||
If the frames were generated successfully or an error occurred you will see a message. | If the frames were generated successfully or an error occurred you will see a message. | ||
===Creating binary command blocks=== | |||
This part can be found on the second tab on the right side. To create these command blocks just follow the steps 1-3 above. After you have done this enter the name (and path) of the command file and press the “Generate ...” button right beside. If the block was generated successfully or an error occurred you will see a message.<br> | This part can be found on the second tab on the right side. To create these command blocks just follow the steps 1-3 above. After you have done this enter the name (and path) of the command file and press the “Generate ...” button right beside. If the block was generated successfully or an error occurred you will see a message.<br> | ||
<br> | <br> | ||
===Uploading to a dedicated location=== | |||
To load the files that were generated to the place they are needed an uploading feature was introduced. Here you enter the hostname to where you want to load the files up. Authenticating at the host is done by entering username and password. After that you are able to specify a local file/folder that has to be loaded up and a remote directory where the files/folder is saved to.<br><br> | To load the files that were generated to the place they are needed an uploading feature was introduced. Here you enter the hostname to where you want to load the files up. Authenticating at the host is done by entering username and password. After that you are able to specify a local file/folder that has to be loaded up and a remote directory where the files/folder is saved to.<br><br> | ||
===NOTE=== | |||
The remote directory must exist and local directories that contain subdirectories can not be loaded up<br> | |||
E.g. you want to load the files to “/tmp/test” the “test” directory has to be created before uploading. | E.g. you want to load the files to “/tmp/test” the “test” directory has to be created before uploading. | ||
Revision as of 10:56, 23 August 2010
Frame Generation Tool
General
This tool can be used to generate frames for any Xilinx Virtex-II Pro FPGA. Therefore an XML based configuration file exists. To generate frame files the type of FPGA has to be added to the XML file.
This is done in the following way:
<Device DeviceName="XC2VP7" DeviceID="0124A093" numFrames="1320" frameLength="106" IOBColumns="2" IOBFrames="4" IOIColumns="2" IOIFrames="22" CLBColumns="34" CLBFrames="22" BRAMColumns="6" BRAMFrames="64" BRAMICColumns="6" BRAMICFrames="22" GCLKColumns="1" GCLKFrames="4">
The device name can be found directly on the chip. The other values are provided in the Xilinx User Guide in the chapter “Configuration – Configuration Details”. There you will find two tables in which all frame and column sizes are listed. The device IDs you will also find in a table in this chapter.
For different types of Virtex FPGAs the names of the frame types can vary. The names shown above are an example for Virtex-II Pro frames.
Creating frames
Generating the frames is done in these steps: 1. Load the bit-file for the FPGA 2. Type the name of the device as you can see above in “DeviceName” 3. Load the XML configuration file 4. Type the directory where the frames are saved to 5. Press the “Split” button If the frames were generated successfully or an error occurred you will see a message.
Creating binary command blocks
This part can be found on the second tab on the right side. To create these command blocks just follow the steps 1-3 above. After you have done this enter the name (and path) of the command file and press the “Generate ...” button right beside. If the block was generated successfully or an error occurred you will see a message.
Uploading to a dedicated location
To load the files that were generated to the place they are needed an uploading feature was introduced. Here you enter the hostname to where you want to load the files up. Authenticating at the host is done by entering username and password. After that you are able to specify a local file/folder that has to be loaded up and a remote directory where the files/folder is saved to.
NOTE
The remote directory must exist and local directories that contain subdirectories can not be loaded up
E.g. you want to load the files to “/tmp/test” the “test” directory has to be created before uploading.
