Busy Box and related/BusyBox Registers

Busy Box Status and Contol Registers
Name	Address	Mode	Description	Default Value
TX module(15:0)	0x0001	RW	For sending messages to DRORCs. Bit 7:0 is TX data. Bit 15:8 gives channelnumber in hexadecimal. Any value greater than the actual number of channels will result in a broadcast on all channels.	0x0000
RX memory	0x1000-0x1FFF	RW	Memory where all messages received from DRORCs will be stored. One message is stored over 4 addresses: Address ending "00" - DRORC Message(47:32) Address ending "01" - DRORC Message(31:16) Address ending "10" - DRORC Message(15:0) Address ending "11" - Receiving Channel number(7:0)	0x0000
RX memory pointer(13:0)	0x2000	R	Holds the value where the next message will be written in RX memory. The RX memory pointer will increase by 4 for each message.	0x0000
EventID FIFO count(3:0)	0x2001	R	Number of eventIDs stored in the FIFO, excluding the eventID currently being matched, if any.	0x0000
Current EventID(35:32)	0x2002	R	The EventID which is currently being matched.	0x0000
Current EventID(31:16)	0x2003	R		0x0000
Current EventID(15:0)	0x2004	R		0x0000
Newest EventID(35:32)	0x2005	R	The EventID most recently received from the Trigger system.	0x0000
Newest EventID(31:16)	0x2006	R		0x0000
Newest EventID(15:0)	0x2007	R		0x0000
L0 Trigger Timeout(15:0)	0x2008	RW	Time in 10 us resolution the 'busy' will be asserted after an L0 trigger. Note: The busy will not be deasserted if the buffers are full.	0x000A
Busy Condition(15:0)	0x2009	RW	Status and control registers concerning the BUSY generation Bit 15 - Busy because TTCrx_ready is low. Bit 14 - Busy because MEB count >= MEB limit Bit 13 - Busy because L0 timeout is active. Bit 12 - Busy because Trigger Receiver Module is busy receiving a sequence. Bit 11:8 - Unused Bit 7:4 - Current MEB count. Bit 3:0 - MEB Limit: Limit for the maximum number of MEBs to count before busy will be asserted.	0x0000
Halt FSM matching(0)	0x200A	RW	If LSB is set to 1 the internal State Machine (FSM) will halt in a wait state and will stop requesting EventIDs from the DRORCs.	0x0001
Force match(0)	0x200B	T	Writing 0x1 when FSM halt is set, will force the FSM to move on to the next EventID even if it is not matched. Note : FSM must be halted before this has any effect.	N/A
Re-Request Timeout(15:0)	0x200C	RW	Number of clock cycles (25 ns) to wait in between sending requests to the DRORCs.	0x07FF
Current RequestID(3:0)	0x200D	R	Holds the RequestID the BusyBox is using to request eventIDs from the DRORCs.	0x0000
Retry Count(15:0)	0x200E	R	Number of times the FSM has sent requests to DRORCs. Will reset to 0 for start of every eventID.	0x0000
Busy time(31:16)	0x2010	R	Holds value of counter for number of clock cycles BUSY has been asserted.	0x0000
Busy time(15:0)	0x2011	R		0x0000
RX mem filter(15:0)	0x2012	RW	Allows filtering of messages that are stored in RX memory. Bit 7:0 is the pattern that will be matched with the channelnumber of the message. Bit 15:8 allows enableing matching of individual bits 7-0.	0x0000
Number of Channels	0x2014	R	Number of channels (in hexadecimal) the firmware includes. This is a generic set at compile-time.	N/A
Firmware Revision	0x2015	R	Firmware revision in hexadecimal. Holds the revision number of the source in SVN that this FW was compiled from. Current : 34	0x0022
Stresstest Enable(0)	0x2016	RW	Duplicates input on channel 0 to all other channels. Used for testing the device with all channels enabled when only one physical DRORC is available.	0x0000
Channel Registers	0x21XX	RW	'XX' in the address gives the channelnumber in hexadecimal. Bit 0 is enable(1)/disable(0) Bit 1 indicates that the current EventID has been matched on this channel.	0x0001

Trigger Receiver Module Status and Contol Registers
Name	Address	Mode	Description	Default Value
Control(15:0)	0x3000	RW	[0] Serial B on/off	1
		RW	[1] Disable error masking	0
		RW	[2] Enable RoI Decoding	0
		RW	[3] L0 Support	1
		R	[4:7] Unused	N/A
		RW	[8] L2Accept Event FIFO storage mask	1
		RW	[9] L2Reject Event FIFO storage mask	1
		RW	[10] L2Timeout Event FIFO storage mask	1
		RW	[11] L1message mask	1
		RW	[12] Trigger Input Mask Enable	0
		RW	[13:15] Unused	N/A
Control(7:0)	0x3001	R	[0] Bunschcounter overflow	N/A
		R	[1] Run Active	N/A
		R	[2] Busy receiving trigger sequence	N/A
		R	[3] Unused	N/A
		R	[7:4] CDH version	0x2
		R	[15:8] Trigger Receiver version	0x13
Reset Counters	0x3002	T	[0] Reset all counters in the Trigger Receiver	N/A