MikroserverSetup - Revision history

Nfyku at 11:52, 30 May 2024

2024-05-30T11:52:52Z

← Older revision		Revision as of 11:52, 30 May 2024
Line 2:		Line 2:

	This setup process will allow you to connect to the mikroservers with one command without typing any password or long host names.		This setup process will allow you to connect to the mikroservers with one command without typing any password or long host names.

	~~There are 4 mikroservers at IFT, mikroserver1 through mikroserver4.~~

	== SSH key ==		== SSH key ==
Line 10:		Line 8:
	To generate a key, type into the terminal		To generate a key, type into the terminal
	ssh-keygen		ssh-keygen
	This will generate the files id_rsa and id_rsa.pub in the folder ~/.ssh, where the latter is the public key that needs to be stored on the server. Copy the key with your identity to ~~either mikroserver~~ (~~mikroserver3 is chosen in this example, but~~ since the user environment is shared for each server, this will give you access to all the servers). You can do this manually, but the easiest way is to use the ssh-copy-id utility. NB: Replace USERNAME with your username		This will generate the files id_rsa and id_rsa.pub in the folder ~/.ssh, where the latter is the public key that needs to be stored on the server. Copy the key with your identity to any of the mikroservers (since the user environment is shared for each server, this will give you access to all the servers). You can do this manually, but the easiest way is to use the ssh-copy-id utility. NB: Replace USERNAME with your username and mikroserver with the full name of your preferred mikroserver.
	ssh-copy-id USERNAME@~~mikroserver3.ift.uib.no~~		ssh-copy-id USERNAME@mikroserver
	You will be prompted your password. After the key is copied, you should be able to login with "ssh USERNAME@~~mikroserver3.ift.uib.no~~" without having to enter your password.		You will be prompted your password. After the key is copied, you should be able to login with "ssh USERNAME@mikroserver" without having to enter your password.

	== Connection aliases ==		== Connection aliases ==
Line 20:		Line 18:
	To do this, type "gedit ~/.ssh/config" in the terminal.		To do this, type "gedit ~/.ssh/config" in the terminal.
	This will open up an empty file, and here you can store shorthand names and specific SSH settings for the connection, such as your username.		This will open up an empty file, and here you can store shorthand names and specific SSH settings for the connection, such as your username.
	Host ~~mikroserver3~~		Host mikroserver
	HostName ~~mikroserver3.ift.uib.no~~		HostName mikroserver
	User USERNAME		User USERNAME
	Port 22		Port 22
	ForwardX11 yes		ForwardX11 yes
	ForwardX11Trusted yes		ForwardX11Trusted yes
	Copy and repeat this for each server in the same file, remembering to change the hostname to the corresponding mikroserver for each entry. ForwardX11 allows you to launch software on the server itself, while displaying the GUI remotely to the lab PC.		Copy and repeat this for each server in the same file, remembering to change the hostname to the full name of the corresponding mikroserver for each entry. ForwardX11 allows you to launch software on the server itself, while displaying the GUI remotely to the lab PC.

	After saving the file, you should be able to simply write "ssh ~~mikroserver3~~" in the terminal to login to ~~mikroserver3~~.		After saving the file, you should be able to simply write "ssh mikroserver" in the terminal to login to the chosen mikroserver.
	Note: If you are attempting to do this step remotely from the UiB login server you need to use a terminal-based editor like Vim, or connect to the login-server with		Note: If you are attempting to do this step remotely from the UiB login server you need to use a terminal-based editor like Vim, or connect to the login-server with
	ssh -Y USERNAME@login.uib.no		ssh -Y USERNAME@login.uib.no
Line 48:		Line 46:
	ssh -Y USERNAME@login.uib.no		ssh -Y USERNAME@login.uib.no

	The -Y enables trusted X11 forwarding. From here, you can "ssh ~~mikroserver3~~" just as you would from the lab PC and run software. The steps described above (SSH keys and config files) can be repeated on your personal Linux/macOS PC to simplify connecting to the UiB loginserver. On Linux, the configuration file is located in "~/.ssh/config" just as on the server, while on macOS it is located in "/private/etc/ssh/ssh_config".		The -Y enables trusted X11 forwarding. From here, you can "ssh mikroserver" just as you would from the lab PC and run software. The steps described above (SSH keys and config files) can be repeated on your personal Linux/macOS PC to simplify connecting to the UiB loginserver. On Linux, the configuration file is located in "~/.ssh/config" just as on the server, while on macOS it is located in "/private/etc/ssh/ssh_config".

	=== Windows ===		=== Windows ===
Line 64:		Line 62:

	as server address type:		as server address type:
	sftp://mikroserver3/home/USERNAME		[sftp://mikroserver3/home/USERNAME sftp://mikroserver/home/USERNAME]
	to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])		to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])
	To store this connection, right click the "~~mikroserver3~~"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.		To store this connection, right click the "mikroserver"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.

	=== Alternative way using scp/secure copy===		=== Alternative way using scp/secure copy===
	If for some reason the above doesn’t work you can try this:		If for some reason the above doesn’t work you can try this:
	* connect to your mikroserver ~~(ssh mikroserver3)~~		* connect to your mikroserver
	* locate the file you want to copy. i.e /home/USERNAME/picture.jpg		* locate the file you want to copy. i.e /home/USERNAME/picture.jpg
	* type this command		* type this command

Bhu006: Included Windows X11 forwarding

2020-05-03T12:44:05Z

Included Windows X11 forwarding

← Older revision		Revision as of 12:44, 3 May 2020
Line 1:		Line 1:
	= Setup of connection to mikroservers=		= Setup of connection to mikroservers=

	This setup process will allow you to connect to the mikroservers with one command without typing any password or host-names.		This setup process will allow you to connect to the mikroservers with one command without typing any password or long host names.

	There are 4 mikroservers at IFT, mikroserver1 through mikroserver4.		There are 4 mikroservers at IFT, mikroserver1 through mikroserver4.
Line 16:		Line 16:
	== Connection aliases ==		== Connection aliases ==

	Now that you can login without typing your password, it is also convenient to set up ~~host names~~ for the servers to connect quicker.		Now that you can login without typing your password, it is also convenient to set up aliases for the servers to connect quicker.

	To do this, type "gedit ~/.ssh/config" in the terminal.		To do this, type "gedit ~/.ssh/config" in the terminal.
	This will open up an empty file, and here you can store ~~short~~ names and specific SSH settings for the connection, such as your username.		This will open up an empty file, and here you can store shorthand names and specific SSH settings for the connection, such as your username.
	Host mikroserver3		Host mikroserver3
	HostName mikroserver3.ift.uib.no		HostName mikroserver3.ift.uib.no
Line 41:		Line 41:

	== Accessing the lab software remotely on your private PC ==		== Accessing the lab software remotely on your private PC ==
	You do not need to set up a VPN to access the lab software from home. By connecting to the mikroservers through the UiB loginserver with X11 forwarding enabled, you can run the software from any network. You can do this directly on Linux/macOS by using SSH in the bash terminal. For Windows, you will need to download the ~~TTY~~ software [https://~~www~~.~~putty.org~~/ ~~PuTTY~~] to enable X11 forwarding.		You do not need to set up a VPN to access the lab software from home. By connecting to the mikroservers through the UiB loginserver with X11 forwarding enabled, you can run the software from any network. You can do this directly on Linux/macOS by using SSH in the bash terminal. For Windows, you will need to download the X server software [https://sourceforge.net/projects/xming/ Xming] to enable X11 forwarding. This install comes with PuTTY, an SSH client we will use to connect to the Linux based UiB server.

	=== Linux/macOS ===		=== Linux/macOS ===
	The process is the same for both Linux and macOS, except that for macOS you first have to install the X11 server software named XQuartz.		The process is the same for both Linux and macOS, except that for macOS you first have to install the X11 server software named [https://www.xquartz.org/ XQuartz].
	Then, simply connect to the login server by typing		Then, simply connect to the login server by typing
	ssh -Y USERNAME@login.uib.no		ssh -Y USERNAME@login.uib.no
Line 51:		Line 51:

	=== Windows ===		=== Windows ===
			Install Xming and make sure you include PuTTY in the install. Run Xming. It will start minimized, and does not require any setup.
			When first opening PuTTY, you will be presented with this configuration menu. Fill in the hostname "login.uib.no", but don't connect yet.
			[[File:Puttylogin.png]]
			Navigate to Connection -> SSH -> X11, and check Enable X11 forwarding, and type in "localhost:0.0" as X display location.
			[[File:Puttyx11.png]]
			Return to Session, and make sure connection type is set to SSH. Press "Default Settings" and Save to save this configuration for later. Press Open to connect to the server. Enter your username and password, and now you should be in the Linux terminal for the UiB login server. Try to run "gedit" to confirm that you can run a graphical interface. From here you can ssh to the mikroservers and launch software as on the lab computer. Confirm by running gedit on the mikroserver as well to see that you can tunnel X11 through the login server correctly.

	== Add mikroserver as a folder on your pc ==		== Add mikroserver as a folder on your pc ==

	Open up your home folder in ~~linux~~ and in the bottom left corner click "Connect to Server" as shown in this picture:		Open up your home folder in Linux and in the bottom left corner click "Connect to Server" as shown in this picture:
	[[File:ConnectToServer.png\|thumbnail]]		[[File:ConnectToServer.png\|thumbnail]]

Bhu006 at 14:30, 2 May 2020

2020-05-02T14:30:17Z

← Older revision		Revision as of 14:30, 2 May 2020
Line 36:		Line 36:
	There are two main files of sourcing scripts in a Linux environment. One is the file .bashrc, and the other is the file .profile. The difference in these is that the contents of .profile is executed upon login, and .bashrc is executed every time you access the terminal. .bashrc is not sourced to the system by itself upon login, so we need to source .bashrc in .profile manually to use it. This must be done after connecting to one of the mikroservers.		There are two main files of sourcing scripts in a Linux environment. One is the file .bashrc, and the other is the file .profile. The difference in these is that the contents of .profile is executed upon login, and .bashrc is executed every time you access the terminal. .bashrc is not sourced to the system by itself upon login, so we need to source .bashrc in .profile manually to use it. This must be done after connecting to one of the mikroservers.

	echo "source ~/.bashrc" >> ~./profile		echo "source ~/.bashrc" >> ~/.profile

	Scripts can be sourced either within .profile or .bashrc. This will make sure the scripts are loaded every time you log in, so you don't have to do it manually every time.		Scripts can be sourced either within .profile or .bashrc. This will make sure the scripts are loaded every time you log in, so you don't have to do it manually every time.

Bhu006: Fjernet oppsett av Cadence fra artikkelen siden det dekkes av andre artikler (og stoffet var utdatert). Ryddet opp generelt.

2020-05-02T14:24:57Z

Fjernet oppsett av Cadence fra artikkelen siden det dekkes av andre artikler (og stoffet var utdatert). Ryddet opp generelt.

← Older revision		Revision as of 14:24, 2 May 2020
Line 1:		Line 1:
	= ~~Set-up~~ of connection to mikroservers ~~and cadence virtuoso~~ =		= Setup of connection to mikroservers=

	This ~~set-up~~ will allow you to connect to the mikroservers ~~and/or start Cadence virtuoso~~ with one command without typing any password or host-names.		This setup process will allow you to connect to the mikroservers with one command without typing any password or host-names.

			There are 4 mikroservers at IFT, mikroserver1 through mikroserver4.

	~~'''NB: This setup~~ is ~~for TSMC~~, ~~but~~ the ~~commands can be tweaked to be used with IHP or AMS too~~.~~'''~~		== SSH key ==
			To login to the server without having to type in your password every time, we can use SSH key pairs. The public key is stored on the server, and you have your private key stored on the UiB login server.

	~~There are 4 mikroservers~~, ~~mikroserver1~~-~~mikroserver4~~		To generate a key, type into the terminal
			ssh-keygen
			This will generate the files id_rsa and id_rsa.pub in the folder ~/.ssh, where the latter is the public key that needs to be stored on the server. Copy the key with your identity to either mikroserver (mikroserver3 is chosen in this example, but since the user environment is shared for each server, this will give you access to all the servers). You can do this manually, but the easiest way is to use the ssh-copy-id utility. NB: Replace USERNAME with your username
			ssh-copy-id USERNAME@mikroserver3.ift.uib.no
			You will be prompted your password. After the key is copied, you should be able to login with "ssh USERNAME@mikroserver3.ift.uib.no" without having to enter your password.

	== ~~SSH key~~ ==		== Connection aliases ==
	* Generate an ssh-key
	~~ssh-keygen -f ~/.ssh/id.rsa -t rsa -N ''~~

	* Copy the ~~key with your identity~~ to ~~your chosen mikroserver (mikroserver3 is chosen in this example)~~. ~~NB: Replace USERNAME with your user name~~		Now that you can login without typing your password, it is also convenient to set up host names for the servers to connect quicker.

	~~ssh-copy-id~~ USERNAME~~@mikroserver3~~		To do this, type "gedit ~/.ssh/config" in the terminal.
			This will open up an empty file, and here you can store short names and specific SSH settings for the connection, such as your username.
			Host mikroserver3
			HostName mikroserver3.ift.uib.no
			User USERNAME
			Port 22
			ForwardX11 yes
			ForwardX11Trusted yes
			Copy and repeat this for each server in the same file, remembering to change the hostname to the corresponding mikroserver for each entry. ForwardX11 allows you to launch software on the server itself, while displaying the GUI remotely to the lab PC.

			After saving the file, you should be able to simply write "ssh mikroserver3" in the terminal to login to mikroserver3.
			Note: If you are attempting to do this step remotely from the UiB login server you need to use a terminal-based editor like Vim, or connect to the login-server with
			ssh -Y USERNAME@login.uib.no
			to enable the use of graphical editors such as gedit.

	== ~~Connection aliases~~ ==		== Automatic sourcing ==
			There are two main files of sourcing scripts in a Linux environment. One is the file .bashrc, and the other is the file .profile. The difference in these is that the contents of .profile is executed upon login, and .bashrc is executed every time you access the terminal. .bashrc is not sourced to the system by itself upon login, so we need to source .bashrc in .profile manually to use it. This must be done after connecting to one of the mikroservers.
	~~For ease~~ of ~~use set up aliases for~~ the ~~connections~~ in ~~your~~ terminal. ~~Open~~ .bashrc in ~~a text editor (vim / nano) and type in this~~

	~~alias mikroserver1='ssh -X USERNAME@mikroserver1'~~		echo "source ~/.bashrc" >> ~./profile
	~~alias mikroserver2='ssh -X USERNAME@mikroserver2'~~
	~~alias mikroserver3='ssh -X USERNAME@mikroserver3'~~

	~~Also create another alias for your favourite mikroserver~~		Scripts can be sourced either within .profile or .bashrc. This will make sure the scripts are loaded every time you log in, so you don't have to do it manually every time.
	~~echo "alias mikroserver=~~'~~ssh -X USERNAME@mikroserver3'" >> ~/~~.~~bashrc~~

			== Accessing the lab software remotely on your private PC ==
			You do not need to set up a VPN to access the lab software from home. By connecting to the mikroservers through the UiB loginserver with X11 forwarding enabled, you can run the software from any network. You can do this directly on Linux/macOS by using SSH in the bash terminal. For Windows, you will need to download the TTY software [https://www.putty.org/ PuTTY] to enable X11 forwarding.

	== ~~Automatic sourcing~~ ==		=== Linux/macOS ===
			The process is the same for both Linux and macOS, except that for macOS you first have to install the X11 server software named XQuartz.
			Then, simply connect to the login server by typing
			ssh -Y USERNAME@login.uib.no

	~~Source scripts inside~~ .~~bashrc. This will make sure the scripts are loaded every time you log in~~, so you ~~don't have to do it manually~~		The -Y enables trusted X11 forwarding. From here, you can "ssh mikroserver3" just as you would from the lab PC and run software. The steps described above (SSH keys and config files) can be repeated on your personal Linux/macOS PC to simplify connecting to the UiB loginserver. On Linux, the configuration file is located in "~/.ssh/config" just as on the server, while on macOS it is located in "/private/etc/ssh/ssh_config".
	~~# TSMC setup~~
	~~echo~~ "~~source~~ /~~eda/cadence/2018-19/scripts/analog~~.sh" >> ~/.~~bashrc~~
	~~echo~~ "~~source /eda/cadence/eda_general_init.sh~~" ~~>> ~~~/~~.bashrc~~
	~~# IHP setup~~
	~~echo "source ~~~/~~ihp~~/~~cds~~/~~sh.cadence~~" ~~>> ~/~~.~~bashrc~~

	== ~~Commands to run virtuoso remotely~~ ==		=== Windows ===
	~~Then finally on the computers in the lab (NOT connected to the mikroservers)~~
	~~echo "alias virtuoso_tsmc~~=~~"ssh -X USERNAME@mikroserver3 'cd tsmc;virtuoso &'"" >> ~/.bashrc~~
	~~echo "alias virtuoso_ihp~~=~~"ssh -X USERNAME@mikroserver3 'cd ihp/cds;virtuoso &'"" >> ~/.bashrc~~

	~~The next time you open your terminal on your computer you can type~~
	~~virtuoso_tsmc~~
	~~to start Cadence Virtuoso, or~~
	~~mikroserver~~
	~~to connect to mikroserver3 without any hassle!~~

	== Add mikroserver as a folder on your pc ==		== Add mikroserver as a folder on your pc ==
Line 70:		Line 74:

	== Troubleshooting ==		== Troubleshooting ==
	* Make sure you copy your ID (ssh-copy-id) to the correct mikroserver
	* Make sure you have restarted your terminal (or source ~/.bashrc) if the commands doesn't work		* Make sure you have restarted your terminal (or source ~/.bashrc) if the commands doesn't work
	* You have to be either connected to the UiB ~~VPN~~ or run the commands via the computers in the lab to be able to connect to ~~microserver~~		* You have to be either connected to the UiB loginserver or run the commands via the computers in the lab to be able to connect to the mikroservers
	* If you are using another shell like zsh or csh the aliases has to be in ~/.zshrc or ~/.cshrc instead of ~/.bashrc		* If you are using another shell like zsh or csh the aliases has to be in ~/.zshrc or ~/.cshrc instead of ~/.bashrc
	* Make sure you have replaced all the instances of USERNAME with your usename, i.e "abc0123"		* Make sure you have replaced all the instances of USERNAME with your usename, i.e "abc0123"


	[[Category:Mikroelektronikk]]		[[Category:Mikroelektronikk]]

Nfyku: Removed full path references

2020-03-30T07:54:47Z

Removed full path references

← Older revision		Revision as of 07:54, 30 March 2020
Line 4:		Line 4:


	'''''NB: This setup is for TSMC, but the commands can be tweaked to be used with IHP or AMS too.'''''		'''NB: This setup is for TSMC, but the commands can be tweaked to be used with IHP or AMS too.'''


	~~The three mikroservers are :~~
	* mikroserver1.klientdrift.uib.no
	* mikroserver2.klientdrift.uib.no
	* mikroserver3.klientdrift.uib.no

			There are 4 mikroservers, mikroserver1-mikroserver4

	== SSH key ==		== SSH key ==
Line 19:		Line 14:
	* Copy the key with your identity to your chosen mikroserver (mikroserver3 is chosen in this example). NB: Replace USERNAME with your user name		* Copy the key with your identity to your chosen mikroserver (mikroserver3 is chosen in this example). NB: Replace USERNAME with your user name

	ssh-copy-id USERNAME@mikroserver3~~.klientdrift.uib.no~~		ssh-copy-id USERNAME@mikroserver3


Line 26:		Line 21:
	For ease of use set up aliases for the connections in your terminal. Open .bashrc in a text editor (vim / nano) and type in this		For ease of use set up aliases for the connections in your terminal. Open .bashrc in a text editor (vim / nano) and type in this

	alias mikroserver1='ssh -X USERNAME@mikroserver1~~.klientdrift.uib.no~~'		alias mikroserver1='ssh -X USERNAME@mikroserver1'
	alias mikroserver2='ssh -X USERNAME@mikroserver2~~.klientdrift.uib.no~~'		alias mikroserver2='ssh -X USERNAME@mikroserver2'
	alias mikroserver3='ssh -X USERNAME@mikroserver3~~.klientdrift.uib.no~~'		alias mikroserver3='ssh -X USERNAME@mikroserver3'

	Also create another alias for your favourite mikroserver		Also create another alias for your favourite mikroserver
	echo "alias mikroserver='ssh -X USERNAME@mikroserver3~~.klientdrift.uib.no~~'" >> ~/.bashrc		echo "alias mikroserver='ssh -X USERNAME@mikroserver3'" >> ~/.bashrc


Line 45:		Line 40:
	== Commands to run virtuoso remotely ==		== Commands to run virtuoso remotely ==
	Then finally on the computers in the lab (NOT connected to the mikroservers)		Then finally on the computers in the lab (NOT connected to the mikroservers)
	echo "alias virtuoso_tsmc="ssh -X USERNAME@mikroserver3~~.klientdrift.uib.no~~ 'cd tsmc;virtuoso &'"" >> ~/.bashrc		echo "alias virtuoso_tsmc="ssh -X USERNAME@mikroserver3 'cd tsmc;virtuoso &'"" >> ~/.bashrc
	echo "alias virtuoso_ihp="ssh -X USERNAME@mikroserver3~~.klientdrift.uib.no~~ 'cd ihp/cds;virtuoso &'"" >> ~/.bashrc		echo "alias virtuoso_ihp="ssh -X USERNAME@mikroserver3 'cd ihp/cds;virtuoso &'"" >> ~/.bashrc

	The next time you open your terminal on your computer you can type		The next time you open your terminal on your computer you can type
Line 60:		Line 55:

	as server address type:		as server address type:
	sftp://mikroserver3~~.ift.uib.no~~/home/USERNAME		sftp://mikroserver3/home/USERNAME
	to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])		to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])
	To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.		To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.
Line 67:		Line 62:
	If for some reason the above doesn’t work you can try this:		If for some reason the above doesn’t work you can try this:
	* connect to your mikroserver (ssh mikroserver3)		* connect to your mikroserver (ssh mikroserver3)
	* locate the file you want to copy. i.e /home/~~fredrik~~/picture.jpg		* locate the file you want to copy. i.e /home/USERNAME/picture.jpg
	* type this command		* type this command
	scp picture.jpg USERNAME@login.uib.no:path/to/folder/to/copy/to		scp picture.jpg USERNAME@login.uib.no:path/to/folder/to/copy/to
Line 79:		Line 74:
	* You have to be either connected to the UiB VPN or run the commands via the computers in the lab to be able to connect to microserver		* You have to be either connected to the UiB VPN or run the commands via the computers in the lab to be able to connect to microserver
	* If you are using another shell like zsh or csh the aliases has to be in ~/.zshrc or ~/.cshrc instead of ~/.bashrc		* If you are using another shell like zsh or csh the aliases has to be in ~/.zshrc or ~/.cshrc instead of ~/.bashrc
	* Make sure you have replaced all the instances of USERNAME with your usename, i.e "~~fli091~~"		* Make sure you have replaced all the instances of USERNAME with your usename, i.e "abc0123"


	[[Category:Mikroelektronikk]]		[[Category:Mikroelektronikk]]

Nfyku at 14:51, 4 November 2019

2019-11-04T14:51:14Z

← Older revision		Revision as of 14:51, 4 November 2019
Line 38:		Line 38:
	Source scripts inside .bashrc. This will make sure the scripts are loaded every time you log in, so you don't have to do it manually		Source scripts inside .bashrc. This will make sure the scripts are loaded every time you log in, so you don't have to do it manually
	# TSMC setup		# TSMC setup
	echo "source /eda/cadence/~~2016~~-17/scripts/~~analog_flow~~.sh" >> ~/.bashrc		echo "source /eda/cadence/2018-19/scripts/analog.sh" >> ~/.bashrc
	echo "source /eda/cadence/eda_general_init.sh" >> ~/.bashrc		echo "source /eda/cadence/eda_general_init.sh" >> ~/.bashrc
	# IHP setup		# IHP setup

Put009: Added command for copying folders

2018-04-21T17:17:17Z

Added command for copying folders

← Older revision		Revision as of 17:17, 21 April 2018
Line 69:		Line 69:
	* locate the file you want to copy. i.e /home/fredrik/picture.jpg		* locate the file you want to copy. i.e /home/fredrik/picture.jpg
	* type this command		* type this command
	scp picture.jpg USERNAME@login.uib.no:~		scp picture.jpg USERNAME@login.uib.no:path/to/folder/to/copy/to
	* this will copy the file to your home folder on any UiB machine		* this will copy the file to your home folder on any UiB machine
			* To copy a folder
			scp -r NameOfFolder USERNAME@login.uib.no:path/to/folder/to/copy/to

	== Troubleshooting ==		== Troubleshooting ==

Fli091: Formatting

2017-11-14T12:11:21Z

Formatting

← Older revision		Revision as of 12:11, 14 November 2017
Line 64:		Line 64:
	To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.		To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.

	=== Alternative way using scp/secure copy==		=== Alternative way using scp/secure copy===
	If for some reason the above doesn’t work you can try this:		If for some reason the above doesn’t work you can try this:
	* connect to your mikroserver (ssh mikroserver3)		* connect to your mikroserver (ssh mikroserver3)
Line 71:		Line 71:
	scp picture.jpg USERNAME@login.uib.no:~		scp picture.jpg USERNAME@login.uib.no:~
	* this will copy the file to your home folder on any UiB machine		* this will copy the file to your home folder on any UiB machine


	== Troubleshooting ==		== Troubleshooting ==

Fli091: Added alternative way to get your files from mikroserver

2017-11-14T12:10:58Z

Added alternative way to get your files from mikroserver

← Older revision		Revision as of 12:10, 14 November 2017
Line 63:		Line 63:
	to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])		to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])
	To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.		To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.

			=== Alternative way using scp/secure copy==
			If for some reason the above doesn’t work you can try this:
			* connect to your mikroserver (ssh mikroserver3)
			* locate the file you want to copy. i.e /home/fredrik/picture.jpg
			* type this command
			scp picture.jpg USERNAME@login.uib.no:~
			* this will copy the file to your home folder on any UiB machine

Fli091: How to bookmark the mikroserver folder-connection

2017-10-31T10:53:20Z

How to bookmark the mikroserver folder-connection

← Older revision		Revision as of 10:53, 31 October 2017
Line 62:		Line 62:
	sftp://mikroserver3.ift.uib.no/home/USERNAME		sftp://mikroserver3.ift.uib.no/home/USERNAME
	to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])		to add your homefolder on mikroserver as a folder on your local PC for easy access to your files (for example the [[Transistor_operating_point_printer]])
			To store this connection, right click the "mikroserver3"-folder and click "Add Bookmark". The next time you just click the bookmark to open it.